Windows cannot be installed on this drive что это



Решаем проблему с дисками при установке Windows

Невозможна установка Windows на диск

Рассмотрим подробнее саму ошибку. При ее возникновении в нижней части окна выбора диска появляется ссылка, нажатие на которую открывает подсказку с указанием причины.

Причин, вызывающих данную ошибку, всего две. Первая – недостаток свободного места на целевом диске или разделе, а вторая связана с несовместимостью стилей разделов и микропрограммного обеспечения – BIOS или UEFI. Далее мы разберемся, как решить обе этих проблемы.

Вариант 1: Не хватает места на диске

В такую ситуацию можно попасть при попытке установки ОС на диск, который до этого был разбит на разделы. Доступа к софту или системным утилитам мы не имеем, но нам на выручку придет инструмент, «вшитый» в установочный дистрибутив.

Нажимаем на ссылку и видим, что рекомендуемый объем немного больше имеющегося в разделе 1.

Можно, конечно, установить «винду» и в другой подходящий раздел, но в таком случае в начале диска останется пустое место. Мы пойдем другим путем – удалим все разделы, объединив пространство, а затем создадим свои тома. Имейте в виду, что все данные при этом будут удалены.

  1. Выбираем первый том в списке и открываем настройки диска.
  2. Нажимаем «Удалить».

В диалоговом окне с предупреждением жмем ОК.

Теперь переходим к созданию разделов.

Если диск разбивать не требуется, то этот шаг можно пропустить и перейти непосредственно к установке «винды».


Настраиваем необходимый объем тома и нажимаем «Применить».

Установщик сообщит нам, что может быть создан дополнительный системный раздел. Соглашаемся, нажав ОК.

Подробнее: Программы для работы с разделами жесткого диска
Готово, в списке появился том нужного нам размера, можно устанавливать Windows.

Вариант 2: Таблица разделов

На сегодняшний день существует два вида таблиц – MBR и GPT. Одно из главных их отличий – наличие поддержки типа загрузки UEFI. В GPT такая возможность имеется, а в MBR нет. Есть несколько вариантов действий пользователя, при которых возникают ошибки установщика.

  • Попытка установки 32-разрядной системы на GPT-диск.
  • Инсталляция с флешки, содержащей дистрибутив с UEFI, на диск MBR.
  • Установка из дистрибутива без поддержки UEFI на носитель GPT.

Что касается разрядности, то здесь все ясно: нужно найти диск с 64-битной версией Windows. Проблемы же с несовместимостью решаются либо конвертированием форматов, либо путем создания носителя с поддержкой того или иного типа загрузки.

В статье, доступной по ссылке выше, описан только вариант с установкой системы без UEFI на диск GPT. При обратной ситуации, когда у нас установщик UEFI, а диск содержит таблицу MBR, все действия будут аналогичными, кроме одной консольной команды.

ее нужно заменить на

C настройками BIOS также все наоборот: для дисков с MBR нужно отключить UEFI и режим AHCI.

Заключение

Таким образом, мы разобрались в причинах проблем с дисками при установке Виндовс и нашли их решение. Для того чтобы избежать возникновения ошибок в дальнейшем, необходимо запомнить, что на диски GPT можно установить только 64-разрядную систему с поддержкой UEFI или создать такую же флешку. На MBR, в свою очередь, устанавливается все остальное, но только с носителя без UEFI.

Источник

3 Ways to Fix Windows Won’t Install on SSD or HDD

There are 3 situations where Windows 11/10/8/7 won’t install on SSD. Learn the step-by-step guide to make it right.

By Dervish / Last Updated March 7, 2022

Windows unable to install on SSD

Installing Windows 11/10/8/7 on a solid state drive (SSD) will surely make your computer faster. However, it would be frustrating if Windows won’t install on SSD. This article covers 3 situations and provides a corresponding solution so you can fix this effectively.

Situation 1. SSD not recognized by BIOS

Usually, an SSD will be automatically detected in BIOS when you attach it. However, if your SSD is not showing in BIOS, you should check the things belowпј›

1. Check the SSD cable connection. You can simply switch another SATA cable. You can also connect it to an external USB adapter to see if it is a problem of damaged BIOS connection.

2. Check if SATA port is enabled. In some cases, the port is turned OFF in System Setup (BIOS). When you connect a new SSD drive to the system, you may need to manually turn it on before you can see the drive in BIOS.

3. Connect the drive to another working computer to see if the SSD is damaged.

Situation 2. SSD not recognized by Windows 11/10/8/7 Setup

If it is detected in BIOS, then you can refer to the following steps to make it right:

If it is detected in BIOS, then you can refer to the following steps to make it right:

1. Boot into BIOS, and set SATA to AHCI Mode. For installing Windows 8/10/11 cannot install on SSD, enable Secure Boot if it is available.

2. If your SSD still is not showing at Windows Setup, press SHIFT+F10 to open a Command Prompt window.

3. Type “diskpart”

4. Type “list disk” to display all the disks connected to your computer.

5. Type “select disk [disk number]” For example, type “select disk 0” if you have insert one drive in your system

6. Make sure the selected disk has no valuable data. Type “clean all” and press Enter to wipe out all data from the SSD.

7. When the process is complete, type “exit” to close this windows and go back to Windows Setup screen.

After that, you should see the SSD drive appear at Windows Setup. If you think this disk clean process may reduce its lifespan, you can perform a Secure Erase for SSD.

Situation 3. Windows cannot be installed to this disk

If Windows sees the SSD drive, but you can’t install Windows on SSD GPT with an error “Windows cannot be installed to this disk. The selected disk is of the GPT partition style”, you can fix this through changing BIOS settings or converting disk to MBR partition style.

If your computer supports UEFI boot, you can go to BIOS settings and enable UEFI mode. If you only see Legacy boot mode, you can convert the SSD to MBR disk referring to the following.

1. Press Shift+F10 to bring out a command prompt.

2. Type the following:

diskpart

list disk

select disk [disk number]

clean

convert mbr

3. Wait for the process to complete. Till then, go back to Windows installation screen, and then you should be able to install Windows.

If the error message you received is “Windows cannot be installed to this disk. The selected disk has an MBR partition table. On EFI systems, Windows can only be installed to GPT disks”, you can disable UEFI mode and enable Legacy mode, or you can convert SSD to GPT disk.

As mentioned, using diskpart.exe to convert disk to MBR/GPT will completely wipe out everything on the disk. If you do not want the SSD to be erased, there is third party software AOMEI Partition Assistant Standard that allows you to convert disk to MBR/GPT without data loss/removing partitions.

You can download the free version on a working computer and connect your SSD to it as a second drive. To convert drive to GPT/MBR with AOMEI Partition Assistant:

1. Open this software.

2. Right click on the SSD and select Convert to GPT. If your SSD is MBR, select Convert to MBR.

3. Confirm the task and click “Apply” to apply this change.

PS.: You need to uprade AOMEI Partition Assistant to Professional version if you need to convert system disk between MBR and GPT.

This software also allows you to create a bootable media so you can use it on a computer that has no Windows system installed yet. If you want to clone hard drive to SSD instead of fresh install, this software can be of use too. In conclusion, you don’t need to panic when Windows will not install on SSD. You can just follow these steps to fix it based on your own situation.

Источник

Проблема с hdd при установке и после нее (не отображаються диски)

Модератор форума: Barmenchik, Drinko, V-Efremov, sander23, MedMeks
Компьютерный форум » Операционные системы » Windows 10 » Проблема с hdd при установке и после нее (не отображаються диски) (Windows cannot be installed on this disk. The selected disk has an MBR)

Проблема с hdd при установке и после нее (не отображаються диски)

yakymchuk

BB-код ссылки (для форумов):

Итак как и все, захотелось мне попробовать новую винду. скачал, закатал на флешку, запустил установку.

первым делом что выскочило у меня, так это ошибка: Windows cannot be installed on this disk. The selected disk has an MBR, которая означает что ваш диск размечен в таблице MBR и винда хочет другого типа.

ну думаю окей, как это обойти, оказалось не так сложно, на ноуте стоит hdd для информации и ssd для системы. удалил я ssd раздел через Drive Oprions(advanced), что стерло разметку диска и тыкнул на кнопку далее — установка продолжилась. (кстати, форматирование раздела ничего не дает, таблица разметки остается той же. сменить ее можно также специализированными програмами — partition magick и тд.).

установка продлилась 5минут, все удачно поставилось. подгружаю свой профиль майкрософт, кстати вечером того дня когда вышла винда очень глючило подтверждение по смс и почте. пришлось минут 10 ждать чтобы войти в свой профиль. не хотел ставить локальный.

захожу в мой компьютер и вижу что нет ниодного диска hdd. думаю приплыл. смотрю в менеджере дисков они отображаются но как неактивные со знаком восклицания. проблема все та же, диски в другой разметке. смотрю как бы их так конвертнуть чтобы не потерялась информация. решение окакзалось таким же простым как при установке (только тут я ничего не удалял).

итак тыкаем правой кнопкой по This PC / Manage / Storage / Disk management / видим здесь наш диск со знаком восклицания, правой кнопкой мышки нажимаем на нем и выбираем Convert to dynamic disc (там будет кстати только один активный convert). Соглашаемся с конвертированием. и все. диски снова отображаются в This PC

Системный диск конвертировать уже не нужно.

Источник

Fixed Windows Cannot Be Installed on Drive 0 Partition 1

When an installation comes to a halt on disk selection, this is a problem for many users. The common error is — Windows cannot be installed to disk 0 partition 1. When this happens, there are two ways that it can be resolved.

Theo Lucia

Aug 23, 2022 • Filed to: Answer Hard Drive Problems • Proven solutions

Q: How to fix Windows cannot be installed on drive 0 partitions 1?

«Hello, I had some issues with my hard drive, so I decided to format it. Now, I am trying to install new Windows on my computer. However, it is showing me an error that says windows cannot be installed on drive 0 partitions 1. Did you ever face this error during installation? How did you manage to resolve it?»

If you are planning to install your OS, you must copy all your files first. For this reason, you will need a partition or a drive that has a partitioning system. You can opt to save this system as GUID Partitioning Table (GPT) or as Master Boot Record (MBR).

The partitioning system will be installed based on your OS and booting options. GPT will be installed if it boots in UEFI, while the MBR system will be installed if it boots in Legacy BIOS. The difference is that UEFI creates a 500MB partition, while GPT creates 100MB. It is easy to differentiate them during installation. Make sure you select the appropriate partition system to install Windows on the hard disk.

And in this article, I am going to talk about a very common error: Windows Can’t Be Installed to Drive 0 Partition 1. You can learn about two effective solutions to the problems. Let’s get started!

Part 1. Overview of the Error — Windows Cannot Be Installed to Disk 0 Partition 1

During Windows installation, it is common to experience some issues. Windows cannot be installed on this drive is a common error. The big issue with this is that the Windows installation process is inhibited. The error comes with varying messages

A Windows cannot be installed to Disk 0 Partition n will show when you choose any of them. N indicates the partition. You get different messages on the three partitions and this can be quite annoying.

What could be causing such errors? Below we will find out more about it.

1. Causes of the Error

Some users prefer to use an internal SAS controller for a hard drive when installing Windows. If the Master File Table (MFT) is corrupted or the SAS drive has issues, one will get an error. A message Windows cannot be installed to disk 0 partition 1 will pop up. After changes have been done, the Microsoft Windows partition manager (partmgr.sys) is no longer connected to the driver.

When the Boot List Option or the Boot Mode in BIOS settings is set to Unified Extensible Firmware Interface (UEFI and the size of the hard drive is above 2TB.

2. Symptoms of the Error

Windows cannot be installed to disk 0 partition 1 error is common when installing windows on your computer. Even when this happens and you select ‘Next’ on the Window, another error will pop up. Before the installation process is terminated, you will get a message that Windows was unable to install to the selected location. With these errors, your Windows installation process will not be successful.

Part 2. 6 Solutions to Resolve the Error — Windows Can’t Be Installed to Disk 0 Partition 1

If you need the system to boot from GPT partition (it must be GPT) the motherboard must be compatible with UEFI/EFI. If it is not, then the GPT partition must be converted to MBR first. If during installation it asks to install to an NTFS partition, you can choose NTFS during formatting. Alternatively, you can convert FAT to NTFS. NTFS is a file system.

Not understanding your computer’s partitions well will delay you during the installation process. Numerous questions will come up and dealing with them is time-consuming. The question is, is there an easy way to deal with this? The good news is that there is a solution. There are some practical tips you can use to solve the issue.

Most of these issues happen to those using their partitions for the second time. For example, users installing another operating system as a dual boot system. Also, those re-installing Windows. Even with these problems, you can fix them using any of the below two methods.

1. Remove the Partition by Using the Windows Disk Management Tool

The first thing you should do is change the partitions in the drive. Windows comes with a Disk Management tool that you can use to change the partitions. It is quite convenient and useful.

One thing you have to keep in mind that incorrectly using this pre-installed tool in Windows could mess your partitions. You can even lose your crucial files. Thus, it is recommended that if you are not sure how to perform this task, get an expert to do so. This is a powerful tool, and this means you must be sure of how you are using it.

Before you can start to change the partitions, it is important you back up your files. You do not make a small mistake only to end up losing your data. This also goes when you are performing operations on Windows.

Probably, you see no need to keep the partitions on your computer. If this is the case, Use the Windows Disk Management tool on the installation disk to remove them. Below are the steps on how to do this.

Step 1: The first step involves clicking on the «Start» button and right-clicking on «Computer.» From the menu, select «Manage.» This is how you access the Disk Management tool. It is easier when using Windows 10. All you need to do is click on the «Start» button and open the menu, then select «Disk Management.»

Step 2: To highlight a partition, you need to left-click it. You will see «Drive options (advanced),» a blue link that you should click on. Next, choose the «Delete» option.

Note: Keep in mind that this should be done to all the listed partitions. Once this is completed successfully, a «Disk 0 Unallocated Space» message shows up. This shows a single entry.

Step 3: Now you will need to continually install new Windows. To do so, proceed to clock on the «Next» button.

By completing step 3, you should not get windows that cannot be installed on drive 0 partitions 1 windows 10 error.

It is vital to take into account that when installing Windows 10, a hidden «System Reserved» partition will be created. The size of this partition is about 100MB. It contains the recovery environment and boot files. Before you delete anything, make sure that you backup your data.

2. Fix the Error with DiskPart

In the second method, DiskPart is used. The first thing that you need to do is to start the Windows installation process. The system will prompt you to select the drive that you want to install Windows on. This is not complicated as there isn’t much to do. For a DOS window to open, press «Shift+F10.» They should be pressed at the same time.

Step 1: You can also follow this one. In the command prompt window, enter the diskpart command. This will take you to the DISKPART tool. Once the command is entered, the DISKPART command prompt is displayed.

Step 2: The «List Disk» is the next command that you should use after the diskpart one. What does this command do? It displays all the disks connected to your PC at that particular time. When they are listed, you will see Disk 0.

Step 3: Now that you have seen Disk 0, it is time to work with it. In this step, you need to select it. To do so enter the command «select disk 0» or in full «select disk 0.» Any of these entries will work.

Step 4: This step is critical as it deletes the protected partition and everything else in disk 0. You must ensure that you have selected Disk 0 before issuing the command. Once this is done, enter «clean» as your final command.

When done with step 4 successfully, all partitions will be erased, and you will have a new disk. This command only takes a few seconds to work. The next thing is to close the DOS window. The task is not yet completed. Click «Refresh,» then on the listed disk, and then select «Next.» By completing this, you should proceed with the Windows installation.

With these methods, it is easy to solve the ‘windows cannot be installed to this disk 0 partitions 1’ error.

If you want to install Windows, you may get the following error: «Windows can’t be installed on drive 0 partition 1.» This may be due to different factors, however, there are multiple solutions that will help you correct this problem. In this post you will know how to do each task step by step.

3. Erase your drive to avoid compatibility with previous partitioning systems

One way to correct the aforementioned error is by deleting the partition where you will install Windows, thus eliminating any compatibility that interrupts the process. To do so, just follow the following steps:

Step 1 Delete partition

In custom installation mode, you can check the partitions. Click “Delete” to erase the partition where you want to install Windows. A pop-up window will be displayed to confirm this task.

Step 2 Create a new partition

Now click “New” and then modify the size of the partition if you want. Then click “Apply” and the partition will be created. You can click “Next” to continue the Windows installation.

4. Select the correct option for booting, Legacy BIOS or UEFI

You should configure booting depending on the format of your disk. GPT is compatible with UEFI and for MBR it is more convenient to boot through Legacy BIOS, if there is no compatible boot mode, various errors will occur. To change the booting configuration, you will only have to do the following:

While starting up your computer, press F1, F2, F10, F11 or F12 key. This will open the firmware settings. Go to “Advanced Boot Options” and then in “Boot Mode” press “Enter.” Change the configuration to UEFI or Legacy and finally press “Enter” again. Just restart Windows and the new settings will be updated.

5. Change the partitioning table from GPT to MBR

If you have a low-space hard drive and want to install an older version of Windows, you will need to convert the format from GPT to MBR. This will make your device work better and avoid problems like the error we have been addressing. To do this task, you will only have to do the following:

Step 1 Open Disk Management

Right click Windows icon and click “Disk Management.”

Step 2 Delete volume

Find the disk where you want to install Windows. Now right click on a white space and select “Delete Volume…” Take into account that all information will be deleted after selecting this option.

Step 3 Convert GPT disk to MBR

After deleting volume, right click on the same blank space next to the disk title and click “Convert to MBR Disk.” The partition style will be updated and changed to MBR.

Step 4 Assign volume

After deleting volume, the disk space will be unallocated and you cannot use it. You just have to right click on the blank space next to the disk title and select “New Simple Volume…” Then you will have to stipulate the volume size and to type the drive letter, finally the disk will be formatted so you will be able to use it again.

Learn more solutions to change GPT to MBR.

6. Erase partitioning system through command prompt

As mentioned earlier, it is wise to erase the partition to avoid compatibility errors. There is an alternative way to do this using the Command Prompt tool:

Step 1 Open CMD

Hold “Windows” key and press “R” key to open Run tool. Type “cmd” to open Command Prompt.

Step 2 Write the commands to erase partition

Type the following commands, hit “Enter” after each one:

  • diskpart
  • list disk
  • sel disk 1* (change “1” for the number of the disk in which the partition is located)
  • list partition
  • sel partition 1 (change “1” for the number of the partition you want to delete)
  • delete partition override

After this, the partition should be erased and you can create a new one to install Windows.

Conclusion

Errors such as Windows can’t be installed to disk 0 partition 4 is common. This is, especially when the chosen disk has an incorrect partition table style in BIOS settings. The partitioning system must be compatibles and properly set up during installations. The Windows Disk Management tool that comes pre-installed in Windows and DiskPart will help clear these errors. These two will help in clearing Windows cannot be installed on this drive.

The above options are effective in solving Windows installation issues. This assures you that whenever you want to install Windows, you can do it in a stress-free way. This is important to every user who has wasted time and effort trying to perform the task. The advantage of this guide is that it is not complicated.

Can I delete drive 0 partition 1?

Yes, but it means a great risk. Partition 1 of drive 0 is the partition reserved for the operating system; deleting it would mean that Windows would stop working automatically and the information would be completely lost. If you delete this partition, the computer will not function and you using Windows installation media.

Should I format OEM reserved?

The OEM partition is present on the disks since they are created and stores files and archives so that, when the operating system needs to be recovered, the device remains with the factory settings. Formatting it would remove said content and it is not suggested to do so, unless you really need to use the space which that partition is taking up.

What is difference between primary and extended partition?

A primary partition is a division of the disk that the computer recognizes when it starts up, which is why in this type of partitions it usually installs the operating system. On the other hand, secondary or extended partitions are not recognized by the BIOS; therefore, they are used to store data.

How do I add two unallocated partitions?

It can be done through different tasks, but using Windows Disk Management is the most practical way to do it. You just run the application, right click the partition which you want to add the two unallocated spaces and click “Extend Volume” to add the partitions. Wait for the process until it finishes and everything will be ready.

How do I merge unallocated space in C drive?

Like the previous task, you should use Windows Disk Management to complete this process in a practical way. You just have to run the application, right click C drive and click “Extend Volume” to merge the unallocated space. You can choose to add all or just a part of it.

Источник

You may also like...